Products Interface Converters Serial
RS232 Current Loop Converter
ICCL-2 RS232, Current Loop Converter
Current loop devices use current on or current off to transmit binary digits. The ICCL converter interfaces RS-232 systems to 20mA or 60mA current loop ports with open circuit voltages up to 30 V. All the units are very easy to implement. Simply connect the appropriate interface cable and select the DCE/DTE type. Async RS232 short haul modem
IC232IP Async RS232 short haul modem
The IC232IP Asynchronous, Short Haul Modem, overcomes the limited distances of the RS-232 standard by converting DCE/DTE equipment to full duplex 2 twisted pair wire (Category 3 or better). This series of converters works without any external power supply. The ic232IP-SM operates up to 10 Km depending on the wire gauge and data rate. Async RS232 to RS422/RS485, RJ-45 Interface Converter
IC485IP Async RS232 to RS422/RS485, RJ-45 Interface Converter
The IC485IP Interface Converters provide asynchronous conversion between RS-232 interface and RS-485 standard interface. The RS-232 interface connection is via the unit's DB-25 female connector, while the RS-485 side's connection is via either a five screw terminal block or an RJ-45. The ic485IP converter's circuitry is not electrically isolation between the RS-232 and RS-485 sides. The RS-232 side may operate as DTE or DCE, has provisions for establishing hardware flow control, and has LEDs to indicate data transmission and reception. The RS-485 side may operate in either two wire half duplex or four wire half or full duplex and also has LED's to indicate data transmission and reception. RS232 Data Interface Converter
RS232 Data Interface Converter
The RS232IP family of interface converters allows full bi-directional synchronous conversion between RS-232C (V.24) and V.35, X.21 or RS-449/530 hardware. These converters all work WITHOUT an EXTERNAL POWER SUPPLY. The RS232IP interface converters are designed for synchronous RS-232 operation at data rates up to and including 128kbps. They may also be applied to asynchronous RS-232 using only TD & RD signals, while ignoring TC, RC, and XTC timing signals. Asynchronous RS-232 requires three times greater data throughput on the synchronous side's V.35, X.21 or RS-449/530 interface. The physical connections for all RS232IP family converters are DB25 female with standard pin out, while a cable adapter is required for V.35, X.21 or RS-449/530 side. All three models may be interchanged as long as the correct V.35, X.21 or RS-449/530 cable is applied. RS485 Interface Converter
RS485 Interface Converter
The V35/485-1 Interface Converter provides conversion between V.35 and RS-485 standard interfaces. The V.35 interface connection is via a supplied adapter cable and the unit's DB-25 female connector, while the RS-485 side's connection is via a five screw terminal block. The V35/485-1 converter's circuitry provides a high degree of electrical isolation between the V.35 and RS-485 sides. The V.35 side may operate as DTE or DCE, switch selectable, has provisions for establishing hardware flow control, and has LEDs to indicate data transmission and reception. The RS-485 side may operate in either two wire half duplex or four wire half full duplex. V.35 Data Interface Converter
V.35 Data Interface Converter
The V35IP family of interface converters allows full bi-directional synchronous conversion between V.35 and X.21 or RS-449/530 hardware. These converters all work WITHOUT an EXTERNAL POWER SUPPLY. The V35IP interface converters are designed for synchronous V.35 operation at data rates up to and including 2048kbps. They may also be applied to asynchronous V.35 using only TD & RD signals, while ignoring TC, RC, and XTC timing signals. Asynchronous V.35 requires three times greater data throughput on the synchronous side's X.21 or RS-449/530 interface. The physical connections for all V35IP family converters are DB25 female connectors and V.35 adapter cable. The V.35 side requires the supplied DB25 to MB34 adapter cable to connect directly to V.35 equipment. Ethernet to WAN (V.35, RS530, RS449, X.21) bridge
ET100 Ethernet to WAN (V.35, RS530, RS449, X.21) bridge
The ET100 Network Bridge is a high performance remote, self-learning, Ethernet bridge. Its compact size and low cost makes it ideal for cost-sensitive bridging applications, or as a LAN extender or segmenter over bit stream type infrastructures. The built-in n x 64(56)Kbps timing clock generator makes it easy to connect to other n x 64(56)Kbps related data equipment. Several options of data interfaces, including V.35, RS-530, RS-449, X.21 and RS-232, make this unit's connection between 10Base-T or 100Base-TX LAN and various data port interfaces convenient. |
|
|
