NIC - Network Interface Cards
Dual Port SFP+ PCI-e 10GbE Network Adapter
Alloy A10GE2SFP Dual Port SFP+ PCI-e 10GbE Network Adapter
The Alloy A10GE2SFP is a dual SFP+ slot10GbE Network Adapter designed to support high-end servers, enterprise network backbones, and computing infrastructure supporting bandwidth intensive applications. The dual SFP+ slots are used to install SFP+ transceivers for either 10GbE multimode, singlemode or WDM connectivity.
Xframe E
Xframe E - 10 Gigabit Ethernet PCI Express Server & Storage Adapter
Xframe E is the newest member of Neterion’s Xframe 10 Gigabit Ethernet product family. PCI-Express (PCIe) is a next-generation I/O interconnect standard that is rapidly gaining traction in the server and storage world. The pairing of Neterion’s industry-leading Xframe technology with PCIe means that best-in-class Ethernet performance is available to more servers than ever before. The Xframe product family offers a unique multi-channel device model. A total of eight independent transmit and receive paths are available and each path may be prioritized for true Quality-of-Service support. By combining this novel architecture with the power of Extended Message Signalled Interrupts (MSI-X), Neterion has established a leading-edge framework for I/O Virtualization. Xframe II
Xframe II - 10 Gigabit Ethernet PCI-X 2.0 Server & Storage Adapter
Xframe II is a 10 Gigabit Ethernet adapter taking advantage of the PCI-X 2.0 bus architecture. It doubles the data rate delivered by the earlier bus standard (PCI-X 1.0) and unleashes the full line speed of 10 Gb/sec. It allows data center managers faced with exponentially increasing bandwidth needs to boost their network’s performance while preserving their investment in Ethernet. Gigabit Ethernet Adapter
Gigabit Ethernet Adapter
The ALLOY-8169V3 is a high performance 32-bit 10/100/1000 Gigabit Ethernet adapter for networks demanding high bandwidth and flexibility. It features Nway Auto-Negotiation for speed selection of 10Mbps, 100Mbps or 1000Mbps, in half-or full-duplex modes. The ALLOY-8169V3 fully complies with all IEEE 802.3ab, 10/100/1000Base-TX standards. Designed with a Realtek single-chip Gigabit Ethernet LAN controller, the ALLOY-8169V3 is fully compliant with Microsoft® NDIS5 (IP, TCP, UDP) Checksum and Segmentation Task-offload features, and supports IEEE 802.1Q Virtual Local Area Network (VLAN). The above features contribute to lowering CPU utilization while providing performance enhancements when operating in high speed gigabit environments. PCI-E Gigabit 1000Base-SX fibre Network Adapter
PCI-E Gigabit 1000Base-SX fibre Network Adapter
The ALLOY 1000ELC, one of Alloy's 1000E series of PCI-e Gigabit Ethernet Network Adapters, has a maximum range of 550 metres and offers advanced functions such as VLAN filtering. The ALLOY1000ELC fibre Network Adapter is fully compliant with the IEEE 802.3z and 1000Base-SX standards. It provides up to 2000Mbps full duplex connectivity to your existing or newly created Gigabit Ethernet fibre network infrastructure, utilising an LC type connector. With advanced functions such as VLAN filtering, the ALLOY1000ELC is a secure and highly affordable solution for both desktop PC and server network connectivity. The card also offers remote booting capabilities through the use of PXE (Preboot Execution Environment), RPL (Remote Program Load) and BOOTP (Bootstrap protocol). Gem 6400V2 series
Alloy Gem 64 Gigabit NIC Series
The ALLOY GEM64 Gigabit NIC Series is a high performance, cost effective, Fibre Gigabit Ethernet Network Interface card. It is compliant with all the relevant 1000Base-SX and 1000Base-LX standards, and supports SC and LC fibre interfaces. It is PCI 2.2 standards compliant, operates in 32-bit and 64-bit PCI host systems, and supports 33/66Mhz PCI buses at both 5 and 3.3Volts. This enables operation of the card in any PCI format including PCI-X. The Broadcom based controller offers many advanced network features. Host CPU offload support (including TCP/UDP checksum offload), intelligent Interrupt Optimisation, and 9K Jumbo Frame Ethernet packets for maximised network efficiency. Network protocol, configuration, processor specifications, memory, general features and options, and environmental parameters are all important specifications to consider when searching for network cards and network controllers.
10/100Mbps Network Interface Card
10/100Mbps Network Interface Card
The ALLOY-1439XD is a realtek based 10/100Mbps Network Interface card for use in standard PCI servers and workstations. All standard PC Operating Systems supported. It features Nway Auto-Negotiation for speed selection of 10Mbps or 100Mbps, in half-or full-duplex mode. The EtherZIP 100XD fully complies with all IEEE 802.3u, 10/100Base-TX standards. Designed with Realtek single-chip Fast Ethernet LAN controller, the EtherZIP 100XD uses high speed Bus-Mastering DMA to optimize throughput while maintaining low CPU utilization. Additional support for ‘Wake on LAN’ and remote BootROM applications is also provided, while external LED's provide for easy diagnostic's of the cards operation. Extensive Networking Operating System (NOS) drivers are available including, Win XP/2000/NT/98/ME, NetWare, IntraNetware, Linux etc. The ALLOY-1439XD is also available with a Low Profile Bracket. 100Mbps PCI-E Fibre Optic Network Card
100Mb PCI-E Multimode Fibre Optic (SC) Network Adapter. 2Km
The ALLOY102Exx is a 100Mbps PCI-E fibre optic network card designed for modern high reliability managed fibre networks. The adapter is compliant to PCI-E 1.0, 4 fibre termination types are supported, ST, STR, SC and LC. Utilising the new PCI-E standard, the ALLOY102E Series fibre optic network adapters deliver high performance 100Mb Fibre network connectivity. The PCI-Express design gives you the maximum possible bandwidth and bus efficiency as well as lower power consumption. With Software support for most popular Operating Systems including, Windows Server 2003, Vista, XP, 2000, NT, Netware 4.x, Linux, and NDIS2. Alloy-1440 Fibre Family Adapters
ALLOY-1440 Fibre Family Adapters
The ALLOY-1440 is a 100Mbps PCI fibre optic network card designed for modern high reliability managed fibre networks. The adapter is compliant to PCI 2.2 and will support PCI buses with either 5V, 3.3V or dual voltage standard PCI, 64Bit PCI or PCI-X slots. 5 fibre termination types are supported, ST, STR, SC, MT-RJ and VF-45. The Alloy-1440 uses a low profile PCB and can be supplied with either a full height or a low profile (half height) brackets to ensure support for the vast majority of workstations and servers. A wide range of fibre termination options are supported with SC, ST and Ruggedised ST in Multimode, and several variations in single mode. The Alloy-1440 is based on the Via 6105M Rhine chipset which provides Advanced Management and Power Conservation Features. The Via Rhine Chipset enables configuration of advanced features such as Priority Queuing to increase multimedia transfer speeds, VLAN tagging for security, TCP/UDP checksum offloading from the host CPU and adaptive interrupt handling to handle heavy network loads more efficiently. Advanced power management features include low power consumption from the 0.22 micron designed Via 6105M controller. The adapter also supports a remote BootROM socket which can be use with an optional PXE rom for remote booting from Windows based RIS servers. Wake on LAN (WoL) support is provided via the PCI bus as per PCI 2.2 specification, or via a provide cable for motherboards of PCI 2.1 or older specification. 100Base-FX Fibre ExpressCard Network Adapter
100Base-FX Fibre ExpressCard Network Adapter
The EC100FX Series 100Base-FX Fibre Network Adapters are designed to plug into a notebook or desktop computer equipped with an ExpressCard slot. Model EC100FXSC provides SC type connectors. ExpressCard is a open hardware standard developed by the Personal Computer Memory Card International Association (PCMCIA) and issued by the ITU-T. This standard replaces earlier PC Card (also known as PCMCIA card) technology. The host device supports both PCI Express and USB 2.0 connectivity through the ExpressCard slot . Alloy EX100FX Series Network Adapters utilise the PCI Express connectivity. The major benefit of ExpressCard technology over PCMCIA CardBus is a dramatic increase in bandwidth, ExpressCard has a maximum throughput of 2.5 Gbit/s through PCI Express versus CardBus's shared 1.06 Gbit/s bandwidth. ExpressCard devices are hot-pluggable. All models in the EC100FX Series provide fibre optic link capability for notebook PC to connect to fibre networks at 100Mbps data rate over fibre optic multimode cable, with a maximum cable distance of up to 2Km. Diagnostic LEDs are easily visible to support maintenance tasks. A comprehensive Network Operating System (NOS) driver suite supports NetWare, Windows 98/NT/2000/XP/Vista /2003 server/2008 server. Linux and PXE remote boot is available. |
|
|
| Page 1 of 2 |
