Lanode.com

FMUX160 16 x E1 + 4 x 10/100 Ethernet Fibre Multiplexer

The FMUX160 is 1U 19” rack mountable, PDH Fibre Optic Multiplexer that transmits up to 16x E1 + 4 x 10/100Base-T(X) Fast Ethernet over a single fibre optic link. The FMUX160 chassis in available in five different power configurations; single AC, single DC, dual AC, dual DC, or AC+DC. The AC supplies operate from 90 ~ 240VAC while DC supplies operate from 18~72VDC. On the rear of the chassis, the BNC model provides 16 unbalanced 75 Ohm coaxial connections with BNC connector while the RJ-45 model provides 16 balanced 120 Ohm connections over twisted pair wiring with RJ45 connectors . With two SFP sockets on fibre ports, the FMUX160 gives you the fibre cabling connector SFP-LC, both multi-mode and single-mode are available as well as BiDi which allows bi-directional transmissions using only a single fibre cable. 1+1 Automatic optical line protection is also supported for the aggregate fibre ports. The standard FMUX160 configuration may be viewed or set via serial VT-100 terminal connection or SNMP card with web, telnet, and SNMP management.

FMUX1600 16 x E1/T1 + 4x GbE, RJ45 Fibre Managed Multiplexer

The FMUX1600 is 1U 19” rack mountable, PDH Fibre Optical Multiplexer that transmits up to 16/8 E1/T1 + 4 x 10/100/1000Base-T Gigabit Ethernet over a single fibre optic link. The FMUX1600 chassis is available in three different power configurations; single AC, single DC or AC+DC. The AC supplies operate from 90 ~ 240VAC while DC supplies  operate from 18~72VDC. On the rear of the chassis, the BNC model provides 32/16 unbalanced 75 Ohm coaxial connections with BNC connectors while the RJ-45 model provides 16 balanced 120 Ohm connections over twisted pair wiring with RJ45  connectors. With two SFP sockets on fibre ports, the FMUX1600 gives you the fibre cabling connector SFP-LC - both multi-mode and single-mode are available as well as BiDi which allows bi-directional transmissions using only a single fibre cable. 1+1 Automatic optical line protection is also supported for the aggregate fibre ports. The standard FMUX1600 configuration may be viewed or set via serial VT-100 terminal connection or SNMP card with web, telnet, and SNMP management.

The FMUX20 is a 2U high 19" Rack, 20-slot modular Fibre Optic Multiplexer rack. It provides an economic solution in high density fibre multiplexer installations in central offices. All critical components, Power, fans, management module and interface cards are hot swappable, allowing online field replacement. The hot-swappable power modules can be chosen from AC100-240V, DC18-36. or DC 36-72V. The chassis also has a pair of alarm relays and is able to stack up to 10 chassis as one management unit.

1-Port E1/T1+100M Ethernet Fibre Multiplexer

The FRM220-FOM01 is a modular design for E1/T1 + Fast Ethernet multi-service to single strand fibre PDH multiplexer. FRM220-FOM01 provides E1/T1 transmission transparently, pure 100Mbps Fast Ethernet simultaneously. The fibre optic line gives you the options to choose from most popular fibre cabling connectors such as, ST, SC, FC or SFP-LC. Both multi-mode and single mode models are available as well as BiDi which allows bi-directional transmissions using only a single fibre cable with SNMP and Web-based management in the FRM220, the Network administrator can monitor, configure and control the activity of each card in the chassis.

4-Port E1/T1+ 100M Ethernet Fibre Multiplexer

The FRM220-FOM04 is a modular design for 4xE1/T1 + Fast Ethernet multi-service to dual strand fibre PDH multiplexer. FRM220-FOM04 provides E1/T1 transmission transparently, pure 100Mbps Fast Ethernet simultaneously. The fibre optic line is based on the SFP technology that allows a flexible use of Multimode or Single mode lines and enable the support of different wavelengths and distances. The use of bi-directional SFPs maximizes the utilization of the fibre optic line and results in saving line costs. The multiplexer is equipped by default with redundant AC and DC power supplies for redundant operation. With SNMP and Web-based management in the FRM220, the Network administrator can monitor, configure and control the activity of each card in the chassis.

4 Channel E1/T1 Plus 100M Ethernet Multiplexer

The FMUX04E is a modular design for 4xE1 + Fast Ethernet multi-service to dual strand fibre PDH multiplexer. FMUX04E provides E1 transmission transparently, pure 100Mbps Fast Ethernet simultaneously. The fibre optic line is based on the SFP technology that allows a flexible use of Multimode or Single mode lines and enable the support of different wavelengths and distances. The use of bi-directional SFPs maximizes the utilization of the fibre optic line and results in saving line costs. The multiplexer is equipped by default with redundant AC and DC power supplies for redundant operation. With SNMP and Web-based management in the FMUX04E, the Network administrator can monitor, configure and control the activity remotely.

FRM220-MX210 2-port Gigabit Ethernet Multiplexer

The FRM220-MX210 is a 2-port Gigabit Ethernet Multiplexer which aggregates two wire-speed Gigabit Ethernet services into one 2.5G uplink, reducing the conversion CAPEX and increasing the fibre utilization effectively. The Multiplexer can be used either in point-to-point topology functioning as a media converter for transporting 2 Gigabit Ethernet services over one fibre or in CWDM systems working as a wavelength converter for extending the system’s transmission capacity doubly. FRM220-MX210 is equipped with one 10/100/1000M RJ-45 network management port and three SFP based ports: two Gigabit Ethernet service ports and one 2.5G uplink port, enabling a flexible application as required and realizing a cost effective remote management. Additionally its advanced features such as downlink and uplink loop back, auto laser shutdown and remote network management provide carriers a flexible, reliable and cost-effective two Gigabit Ethernet over one wavelength conversion solution.

FMUX101 Modularized 16E1/T1 + 4x FE Fibre Managed Multiplexer (E1/T1, Data, Voice, Ethernet)

The FMUX101 is a 1U, 19" rack mountable, PDH fibre optic multiplexer that transmits up to 16 channels plus a 10/100Base-TX Fast Ethernet channel over a single fibre optic link. The FMUX101 chassis supports redundant power and hot swappable design. The AC supplies operate from 90~260VAC while DC supplies operate from 36~72VDC or 20~60VDC. From the rear of the chassis, one to four hot swappable quad E1 or T1 line cards, serial data communications (V.35, X.21, RS-530) or FXO/FXS voice cards are supported. The standard FMUX101 configuration may be viewed or set via the front panel LCD/menu keys, serial VT-100 terminal connection, Telnet, web HTTP or SNMP.

FMUX1001 Modularized 16E1/T1 + 4x GbE Fibre Managed Multiplexer (E1/T1, Data, Voice, Ethernet)

The FMUX1001 is a 1U, 19" rack mountable, PDH fibre optic multiplexer that transmits up to 16 channels plus a 10/100/1000Base-T Fast Ethernet channel over a single fibre optic link. The FMUX1001 chassis suppats redundant power and hot swappable design. The AC supplies operate from 90~260VAC while DC supplies operate from 36~72VDC or 20~60VDC. From the rear of the chassis, one to four hot swappable quad E1 or T1 line cards, serial data communications (V.35, X.21, RS-530) or  FXO/FXS voice cards are supported. The standard FMUX1001 configuration may be viewed or set via the front panel LCD/menu keys, serial VT-100 terminal connection, Telnet, web HTTP or SNMP.

4xE1/T1+ GbE Fibre Multiplexer

The FRM220-GFOM04 is a 4 channel E1/T1 fibre multiplexer with an additional Gigabit Ethernet trunk, plus order wire and clear channel RS-232, constructed as a two slot wide card for the FRM220 series. When the FRM220-GFOM04 card is placed in the FRM220 rack with NMC, the management can view the converter card's status, type, version, fibre link status and alarms. The card can be configured to enable or disable the port, reset the port, and provide local or remote diagnostic loopback. The 1+1 redundant optical aggregate of this multiplexer employs industry standard pluggable optics (SFP) operating at 1.25Mbps data rates. The SFP modules can be chosen to support single-mode, multimode, single fibre bi-directional or Coarse and Dense Wave Division Multiplexing (CWDM and DWDM).